Congratulations to Chuangxin Instruments selling several sets lab equipment to Europe Spain

We're glad to cooperate with our Europe clients from Spain (B&B Trends Sl) in April. He has bought several iec61032 test probes, ball pressure apparatus, spring hammer and 1set power cord flecibility tester from us. This is the first time we cooperate and hoping to have a long term cooperation with B&B Trends SL. 

The details of the products as follows:

Test Probe B

This probe is intended to verify the basic protection against access to hazardous parts. It’s also used to verify the protection against access with a finger.

Technology Parameters

Test probe 13

This pin is intended to verify the protection against access to hazardous live parts in class 0 equipment and class II equipment (see IEC60536).

Technology Parameters

Test probe 18

This probe is intended to simulate access to hazardous parts

by children of more than 36 months and less than 14 years.

Technology Parameter

Test Probe 41

This probe is intended to verify the protection against to

glowing heating elements.

Technology Parameter

CX-07 IEC60335 Finger Nail Probe

Finger nail probe is in accordance with the Figure 7 of IEC60335.1 and GB4706.1. The finger nail probe is mainly used for shocking or the non-removable parts of contacting with moving parts to determine whether it can withstand the mechanical pressure in normal use, to reach the required level of protection test. Exert pressure: 10N, 20N, 30N, 40N, 50N.

Picture:

IEC60068-2-75 Spring Hammer

The spring hammer is applicable to perform these tests for determining the ability of a specimen to withstand specified severities of impact. It’s designed according to IEC60068-2-75 standard.

Types and item No.:

CX-T01: Single Spring Hammer: 0.14J, 0.20J, 0.35J, 0.50J, 0.70J, or 1.0J,

CX-T07: Single Spring Hammer: 2.0J

CX-TF6: Unique Spring Hammer: 0.14J, 0.20J, 0.35J, 0.50J, 0.70J, and 1.0J adjustable

Standard:

The spring hammer conforms to the IEC60068-2-75, IEC884, UL1244, GB/T2423.55-2006, GB4706.1, GB8898 and GB7000 standard.

Table 1 – Relation between IK code and impact energy

CX-Q03 Ball Pressure Test Apparatus

The ball pressure test apparatus is used for testing plastics to which hazardous voltage parts are mounted (i.e. terminal backs, transformer bobbins, etc…) in accordance with most IEC, EN Standards and internationally harmonized UL and CSA Standards (950, 1010, 601, 335, etc.). The unit exerts 20N force on sample. Entirely stainless steel.

Note: this test is required to be conducted in an oven at an elevated ambient temperature.

Parameters:

1. Ball diameter: 5mm (R2.5mm)

2. Test Pressure： 20N±0.2N

3. Material: Stainless Steel

4. Standard: IEC60695-10-2, IEC60335, IEC60601, GB4706.1, GB2099.1 etc.

Power Cord Flexibility Tester
This test checks the protection of the supply cord where it enters the appliance. Appliances provided with a supply cord that are moved while in operation shall be constructed so that the supply cord is adequately protected against excessive flexing where it enters the appliance. This does not apply for appliances with automatic cord reels.
The part of the appliance that includes the inlet opening is fixed to the oscillating member so that, when the supply cord is at the middle of its travel, the axis of the cord where it enters the cord guard or inlet is vertical and passes through the axis of oscillation. The major axis of the section of flat cords shall be parallel to the axis of oscillation. 
The cord is loaded so that the force applied is 
– 10 N, for cords having a nominal cross-sectional area exceeding 0,75 mm2; 
– 5 N, for other cords. 
The distance X, as shown in figure 8, between the axis of oscillation and the point where the cord or cord guard enters the appliance, is adjusted so that when the oscillating member moves over its full range, the cord and load make the minimum lateral movement. 
The oscillating member is moved through an angle of 90° (45° on either side of the vertical), the number of flexion for type Z attachments being 20 000 and for other attachments 10 000. The rate of flexing is 60 per minute. 
NOTE: A flexing is one movement of 90°. 
The cord and its associated parts are turned through an angle of 90° after half the number of flexion, unless a flat cord is fitted. 
During the test, the conductors are supplied at rated voltage and loaded with the rated current of the appliance. 
NOTE: Current is not passed through the earthing conductor.